CR-30 - Revision history

Ezrec: /* Klipper Setup */

2021-05-29T01:16:35Z

Klipper Setup

← Older revision		Revision as of 01:16, 29 May 2021
Line 11:		Line 11:
	== Klipper Setup ==		== Klipper Setup ==

	1. ~~Check out~~ [~~https~~://~~github~~.~~com~~/~~KevinOConnor~~/~~klipper~~ Klipper~~] at git hash d619796495d24d4e4c3e6b9bf2b5842db18b1c01~~		{\| class="wikitable"
			! Package
			! Baud
			! Comment
			\|-
			\| [http://www.evillabs.net/cr-30/klipper_cr-30_wrt.zip klipper_cr-30_wrt.zip]
			\| 230400
			\| Klipper firmware configured for Creality Box w/KlipperWRT
			\|-
			\| [http://www.evillabs.net/cr-30/klipper_cr-30_pi.zip klipper_cr-30_pi.zip]
			\| 250000
			\| Klipper firmware configured for RaspberryPi
			\|}

	<~~nowiki~~>$ git clone https://github.com/KevinOConnor/klipper		# Check out [https://github.com/KevinOConnor/klipper Klipper] at git hash 4f939c18e9ae86ef39d75b710fd1e0c72b46e927
	$ git checkout -b ${USER}/cr30 ~~d619796495d24d4e4c3e6b9bf2b5842db18b1c01~~		#* <pre>git clone https://github.com/KevinOConnor/klipper</pre>
	</~~nowiki~~>		#* <pre>cd klipper</pre>
			#* <pre>git checkout -b ${USER}/cr30 4f939c18e9ae86ef39d75b710fd1e0c72b46e927</pre>
	2. Copy ~~this [http://www.evillabs.net/cr-30/klipper~~.bin ~~klipper.bin]~~ file to your SD card, and power cycle your printer.		# Copy the k''baudrate''.bin file to your SD card, and power cycle your printer.
	a. Firmware update takes approx 30s		#* Firmware update takes approx 30s
	b. Your screen will remain blank - this is normal		#* Your screen will remain blank - this is normal
			# Use the the '''printer.cfg''' from the archive to configure klipper
	3. Use the ~~this [http://www.evillabs.net/cr-30/~~printer.cfg ~~printer.cfg]~~ to configure klipper: (in ~/klipper_config/ for the KlipperWRT setup, or upload via Fluidd/Mainsail)		#* (in ~/klipper_config/ for the KlipperWRT setup, or upload via Fluidd/Mainsail for Pi)
			# Use `service klipper restart` on the Creality Box SSH console, or restart Klipper via the Fluidd/Mainsail interface
	4. Use `service klipper restart` on the Creality Box SSH console, or via the Fluidd/Mainsail interface

Ezrec: /* Klipper Setup */

2021-05-28T12:53:03Z

Klipper Setup

← Older revision		Revision as of 12:53, 28 May 2021
Line 17:		Line 17:
	</nowiki>		</nowiki>

	2. Copy this [~~[Media~~:klipper.bin]] file to your SD card, and power cycle your printer.		2. Copy this [http://www.evillabs.net/cr-30/klipper.bin klipper.bin] file to your SD card, and power cycle your printer.
	a. Firmware update takes approx 30s		a. Firmware update takes approx 30s
	b. Your screen will remain blank - this is normal		b. Your screen will remain blank - this is normal

	3. Use the ~~following~~ printer.cfg to configure klipper: (in ~/klipper_config/ for the KlipperWRT setup, or upload via Fluidd/Mainsail)		3. Use the this [http://www.evillabs.net/cr-30/printer.cfg printer.cfg] to configure klipper: (in ~/klipper_config/ for the KlipperWRT setup, or upload via Fluidd/Mainsail)

	~~[[Media:cr30-printer.cfg]]~~

	4. Use `service klipper restart` on the Creality Box SSH console, or via the Fluidd/Mainsail interface		4. Use `service klipper restart` on the Creality Box SSH console, or via the Fluidd/Mainsail interface

Ezrec: /* CR-30 Belt Printer */

2021-05-28T12:45:35Z

CR-30 Belt Printer

← Older revision		Revision as of 12:45, 28 May 2021
Line 17:		Line 17:
	</nowiki>		</nowiki>

	2. Copy this [[~~File~~:klipper.bin]] file to your SD card, and power cycle your printer.		2. Copy this [[Media:klipper.bin]] file to your SD card, and power cycle your printer.
	a. Firmware update takes approx 30s		a. Firmware update takes approx 30s
	b. Your screen will remain blank - this is normal		b. Your screen will remain blank - this is normal
Line 23:		Line 23:
	3. Use the following printer.cfg to configure klipper: (in ~/klipper_config/ for the KlipperWRT setup, or upload via Fluidd/Mainsail)		3. Use the following printer.cfg to configure klipper: (in ~/klipper_config/ for the KlipperWRT setup, or upload via Fluidd/Mainsail)

	[[~~File~~:cr30-printer.cfg]]		[[Media:cr30-printer.cfg]]

	4. Use `service klipper restart` on the Creality Box SSH console, or via the Fluidd/Mainsail interface		4. Use `service klipper restart` on the Creality Box SSH console, or via the Fluidd/Mainsail interface

Ezrec: Created page with "= CR-30 Belt Printer = File:CR-30.jpg The [https://www.creality.com/goods-detail/creality-3dprintmill-3d-printer Creality CR-30] is a belt printer. == KlipperWRT Setup..."

2021-05-28T12:42:20Z

Created page with "= CR-30 Belt Printer = File:CR-30.jpg The [https://www.creality.com/goods-detail/creality-3dprintmill-3d-printer Creality CR-30] is a belt printer. == KlipperWRT Setup..."

New page

= CR-30 Belt Printer =

[[File:CR-30.jpg]]

The [https://www.creality.com/goods-detail/creality-3dprintmill-3d-printer Creality CR-30] is a belt printer.

== KlipperWRT Setup ==

Reprogram your Creality Box with [https://github.com/ihrapsa/KlipperWrt KlipperWrt] using [https://letsprint3d.net/install-klipper-on-creality-wifi-box/ this guide].

== Klipper Setup ==

1. Check out [https://github.com/KevinOConnor/klipper Klipper] at git hash d619796495d24d4e4c3e6b9bf2b5842db18b1c01

<nowiki>$ git clone https://github.com/KevinOConnor/klipper
$ git checkout -b ${USER}/cr30 d619796495d24d4e4c3e6b9bf2b5842db18b1c01
</nowiki>

2. Copy this [[File:klipper.bin]] file to your SD card, and power cycle your printer.
a. Firmware update takes approx 30s
b. Your screen will remain blank - this is normal

3. Use the following printer.cfg to configure klipper: (in ~/klipper_config/ for the KlipperWRT setup, or upload via Fluidd/Mainsail)

[[File:cr30-printer.cfg]]

4. Use `service klipper restart` on the Creality Box SSH console, or via the Fluidd/Mainsail interface